All products Decision layer Data collection Trip Counting Module
Active safety and control
Engine and thermal management

MetaControl Automatic tipper sheeting system

Cover the load at one touch.

Automatic tipper sheeting that covers the load at a single touch

MetaControl — Automatic tipper sheeting system
50 mMaximum remote control range
80 ACurrent capacity of the motor controller
IP68Dust and water ingress protection
9–36 VOperating voltage, suits 12 V and 24 V vehicles

An open body is a risk, and so is covering it by hand

On a truck carrying bulk loads, pulling the tarp across usually means the driver has to climb onto the body. The job is repeated on every trip and takes time, and when it is skipped or left half done, the load ends up on the road.

Flying load, thrown stones

Sand, gravel, crushed stone and spoil are shaken and blown out of the body. A thrown stone can break the windscreen of the vehicle behind and cause an accident.

A driver climbing onto the body

Covering by hand means climbing onto the body every time. It is one of the main sources of falls from height, slips and strain injuries.

Minutes lost on every trip

Covering and uncovering by hand takes minutes each time. Across a fleet, that time adds up again every day.

Material spilt on the road

A load that is not fully covered spills onto the road and can lead to traffic fines and cancelled trips. Every spill is also lost material.

Dust, rain and snow

An open body spreads dust into its surroundings. Rain and snow reach the unprotected load, and grain, fertiliser and waste get wet.

Covering left to the driver

Whether the tarp goes over at all is left to the driver. How the load is covered varies from truck to truck and from driver to driver.

From the cab or the remote, at a single touch

With remote-controlled tipper sheeting, the driver gives the command without leaving the truck, and the motor carries the tarp from one end of the body to the other. The movement can be stopped at any moment.

The cab control panel (open, close, stop and emergency stop buttons) and the wireless remote
Visualisation: motor, pulleys, slide rails and support bows at the front of the body; the tarp half closed
Visualisation: the tarp stopped half way along the body
Visualisation: the tipper raised, the tarp gathered at the front and open
  1. The cab control panel (open, close, stop and emergency stop buttons) and the wireless remote

    Command

    The driver presses open or close on the control panel or on the remote, which works at up to 50 m.

  2. Visualisation: motor, pulleys, slide rails and support bows at the front of the body; the tarp half closed

    Covering and opening

    A high-torque geared motor drives the bows and the tarp along the rails from one end of the body to the other. When the tarp is fully open or fully closed, the system stops by itself.

  3. Visualisation: the tarp stopped half way along the body

    Stopping and positioning

    The tarp can be stopped at any point, repositioned or gathered back. The emergency stop button cuts the system instantly.

  4. Visualisation: the tipper raised, the tarp gathered at the front and open

    Automatic with MetaDamper

    On a truck fitted with MetaDamper, the tarp opens automatically as the body rises and closes automatically once the truck moves off.

The images for steps 2, 3 and 4 are 3D visualisations of MetaControl; the control panel and remote are the actual product.

Try the panel

The panel shown is the real MetaControl control panel. Press its buttons and the tarp in the 3D scene follows the command. Opening, closing and stopping can also be done from the remote, up to 50 m away.

MetaControl tarp on a tipper body

3D scene: a MetaControl tarp on a tipper body. While the tarp is open, material blows off the load; once it closes, the body is covered.

System off
Cover

Press POWER to start.

MetaControl control panel: POWER, emergency stop, CLOSE, STOP and OPEN buttons with operating instructions

Operating instructions on the panel

  1. For tarp operation, press the button once; do not hold it down.
  2. After opening or closing, switch the control unit off with the POWER button.
  3. In an emergency, use the emergency stop button to cut the system power.

The 3D scene is illustrative; the motion time is not a product figure. Real footage is in the “How it works” and “From the field” sections.

Behind the single touch, an 80 A motor controller

Metadiag MetaControl is built on a high-current motor control system developed for on-vehicle systems and industrial motor applications. The electric tarp system is then made to fit the body of each truck.

Controls

One touch, from the cab or up to 50 m away

One touch, from the cab or up to 50 m away

The tarp opens and closes at a single touch from the cab control panel or from the wireless remote, which reaches up to 50 m. The driver does not leave the truck to cover the load.

Multi-channel remote

The remote is multi-channel, with 1R, 2R, 3R and 4R options, so several trucks on the same site can be controlled independently of each other.

Opens and closes with MetaDamper

On a truck fitted with MetaDamper, the tarp opens automatically as the body rises and closes automatically once the truck moves off. The closing step no longer depends on the driver remembering it.

Manual control module

When the remote is not in use, the tarp can be operated by hand through the manual control module.

Safety

Emergency stop and audible warning

The emergency stop button on the cab panel cuts the system instantly. An audible warning alerts people nearby while the tarp is moving.

Over-current and short-circuit protection

On over-current or a short circuit, a buzzer sounds and the system switches to protection mode. The motor stops by itself when the tarp is fully open or closed, protecting the motor and the mechanism.

Control electronics

80 A, 9–36 V, IP68

The motor controller handles 80 A, runs on 9–36 V and is IP68 rated: heavy-duty power electronics suited to mud, dust and washdowns on site.

Programmable processor and Wi-Fi interface

The programmable processor lets the system be set up for each site. Performance is tracked through the Wi-Fi interface, which requires a username and password to keep out unauthorised changes to the settings.

Tarp and body

Made to fit, three tarp options

Each motorised tipper tarp system is made to fit: the bow structure, the rails and the tarp follow the dimensions of the body. The tarp is chosen to suit the load: mesh, waterproof PVC-coated or reinforced.

From the field

A MetaControl tarp closing on site

Where it works

Construction and earthworks

Sand, gravel, crushed stone, spoil and rubble travel covered, and nobody climbs onto the body to pull the tarp.

Mining

Ore and aggregate travel covered, with less dust and a lower risk of thrown stones.

Agriculture

Grain, feed and fertiliser are protected from rain and snow by a waterproof tarp.

Waste management

Rubble and waste travel covered, lowering the risk of spills on the road.

Logistics and bulk haulage

Industrial bulk products are covered and uncovered at a single touch, saving time between loading and unloading.

Fleets with MetaDamper

The tarp opens as the body rises and closes as the truck moves off; closing it no longer depends on the driver's memory.

Technical specifications

Control electronics

Operating voltage
9–36 V
Current capacity
80 A
Ingress protection
IP68
Processor
Programmable
Interface
Wi-Fi: performance tracking, username and password login
Electrical protection
Buzzer warning and protection mode on over-current or short circuit
End of travel
Automatic stop when fully open or closed

Controls

Cab control panel
Power, open / stop / close, emergency stop; stainless steel panel
Remote control
Wireless, range up to 50 m
Channel options
Multi-channel: 1R / 2R / 3R / 4R
Manual control
Manual control module
Warning
Audible warning
MetaDamper integration
Optional: opens as the body rises, closes when the truck moves off

Mechanics and tarp

Drive
High-torque geared motor
Support structure
Bow structure with slide and guide rails
Tarp options
Mesh, waterproof (PVC-coated), reinforced
Fitting
Made to the dimensions of each body
Vehicle fit
Tipper trucks, trailers, semi-trailers and special bodies

The support structure and the tarp are engineered to the body measurements taken during the site survey.

Part of the ecosystem

MetaControl runs on the vehicle with its own controls; it has no screen in the MetaFMS fleet panel and does not need the panel to work. Paired with MetaDamper, the tarp opens automatically as the body rises and closes automatically once the truck moves off.

Frequently asked questions

Which vehicles and applications is it for?

The automatic sheeting (tarp) system fits tipper trucks, trailers, semi-trailers and special bodies, and each system is made to the dimensions of the body. The motor controller's catalogued working areas also include curtain-sided trailers, tractor-unit systems, roller shutters, workbenches and door systems.

Does it work without MetaDamper?

Yes. MetaControl works on its own: the tarp is opened and closed from the cab panel or the remote. Integration with MetaDamper is optional and adds automatic opening and closing linked to the body's movement.

Which tarp should I choose?

A mesh tarp suits loads that need ventilation, such as sand, gravel and crushed stone; a waterproof PVC-coated tarp suits loads that must stay dry, such as grain, fertiliser and waste. For heavy-duty work with high wear and tear, a reinforced tipper tarp is used.

What happens if something goes wrong while the tarp is moving?

The emergency stop button cuts the system instantly. On over-current or a short circuit, a buzzer sounds and the system switches to protection mode, and the motor stops by itself when the tarp is fully open or closed.

Does it show up in the MetaFMS fleet panel?

No. MetaControl runs on the vehicle and has no screen in MetaFMS. Settings and performance tracking are handled through the unit's Wi-Fi interface, which is protected by a username and password.

How is it installed?

First the body is measured and the system is engineered to those measurements. The support structure and the tarp are made to fit the body, and authorised teams carry out the fitting. Technical support, maintenance and spare parts come from Metadiag's field support.

What is the maximum range of the MetaControl remote?

The MetaControl remote has a range of up to 50 m. The tarp can be opened, closed and stopped at the required point from the cab panel or wireless remote.

MetaControl makes covering the load easier; it does not replace the driver's and the haulier's responsibility for loading, binding and securing the load in line with the law. Traffic and occupational safety rules and the vehicle manufacturer's instructions still apply.

MetaControl

Let's start with a few pilot vehicles in your fleet

We plan the survey, installation and reporting around your site. Our team reviews your vehicles and recommends the right configuration.

Products of interest